This standard is issued under the fixed designation D ; the number immediately following fication System D lists the ASTM materials standards that. ASTM D , defines a punch-type of shear test. This test method covers the procedure for determining the shear strength of composite materials in the form of . ASTM D Standard Test Method for Shear Strength of Plastics by Punch Tool. standard by ASTM International, 05/01/ View all product details.
|Published (Last):||21 May 2004|
|PDF File Size:||13.93 Mb|
|ePub File Size:||17.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D732 Shear Strength of Plastics by Punch Tool
Moreover, the fact that the shear strength is calculated by dividing the load by the area of the shear strength is calculated by dividing the load by the area of the sheared edge circumference X thickness should not be asmt as indicating that the shear strength value so obtained is solely a material property, independent of thickness.
A male punch is then forced through the hole in the metal fixture causing shear along the edge of the hole.
It is intended for use as a materials screening and materials comparison test of plastics available in the form of sheets or molded disks. The shear strength is calculated by dividing the force required to shear the specimen by the area of the sheared edge.
For both fixtures, a specimen in the form of a bar of rectangular cross section is simply placed in a slot in the base and a flat-bottomed guillotine is pressed against the bar, shearing aastm into three pieces. ASTM D test procedure: However, it must d32 recognized that for end-use applications there are likely to be many factors not taken into account in this test method, such as stress-concentrating geometries and rates of shear, which can profoundly affect the measured shear strength.
ASTM D TESTING FIXTURE
Shear strength results are important to designers of film and sheet products that tend to be subjected to shear loads, or in applications where applied crushing loads are a risk. Need help or have a question? Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
Inspection Validating the specifications, value and safety of your raw materials, products and assets.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The results are expressed as shear strength and are given in the units of MPa or psi.
ASTM D732 TESTING FIXTURE
Formally confirming that your products and services meet all trusted external and internal standards. The values given in parentheses are for information only. Assurance Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. However, a uniform shear stress state is not attained; severe stress concentrations occur at the edges of the punch.
Plastics | ASTMD | Prospector
Sources of Additional Information: Global Reach Intertek is the industry leader with over 43, people in 1, locations in over countries. Testing Evaluating how ashm products and services meet and exceed quality, safety, sustainability and performance standards.
This test method is intended as a comparative test, and not as a quantitative measure of the shear strength of the material. Other non-standard, comparative-type punch shear test methods have also been developed. Through astmm network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world.
However, it must be recognized that for end-use application there may be many factors not taken into account in this test method, such as stress-concentrating geometrics and rates of shear, which can profoundly affect shear strength. Select from list below: Specimen thicknesses can range from 0. Touchstone Research Laboratory, Ltd. Due to the very large number of tests offered, descriptions of those most commonly requested have been gathered into the following groups: Figure 2 shows two such fixtures.
As a materials screening test it does have the advantages of requiring a simple specimen and utilizing a simple test procedure. Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world.
What is Third Party Certification and Accreditation for the food industry? Moreover, the fact that the shear strength is calculated by dividing the load by the area of the sheared edge punch circumference X specimen thickness does not interpret as indicating the shear strength value so obtained is solely a material property, independent of thickness. The specimens are usually 2 inich diameter discs or 2 inch squared plates and thickness ranging between 0.
The lower end of the punch is then placed in the hole in the base plate lower left and the cover plate top is bolted on to axtm the specimen securely in place. The area of the sheared edge is equal to the circumference of the punch multiplied by the thickness of the specimen.